MCSE MCITP Boot Camp Training

 
  • Do you want to become MCSE /CCNA ?
     
  • Do you want to finish in 2/3 weeks?

 



 
 
 
 


 
 

 

MCSE Boot Camp, CCNA Bootcamp, CCNP Boot camp training in UK, USA, JAPAN, India
CCNA Training, MCSE Training, A+ Certification, MCSA, CCNP, Network+, Security+, CISSP, MCSD, CCSP,

MCSE Exam, free Real Exam Test, Guide, Prepare MCSE

 

MCSE Boot Camp, CCNA Bootcamps, CCNP Boot camp Certification Training

MCSE Guide

Free MCSE
Free MCSE Training
MCSE
MCSE 2003
MCSE Books
MCSE Boot Camp
MCSE Brain dumps
MCSE Certification
MCSE Exam
MCSE Free
MCSE Jobs
MCSE Logo
MCSE Online
MCSE Online Training
MCSE Practice
MCSE Practice Exams
MCSE Practice Tests
MCSE Requirements
MCSE Resume
MCSE Salary
MCSE Self Paced Training Kit
MCSE Study
MCSE Study Guide
MCSE Study Guides
MCSE Test
MCSE Testing
MCSE Training
MCSE Training Kit
MCSE Training Video
MCSE Windows 2003
Microsoft MCSE Training
Training MCSE
Windows 2003 MCSE

 

 

MCSE : Security Specialist

Error in CONFIG.SYS line XX

Usually caused by a missing/corrupted file or device driver, or typing error.

Bad or missing COMMAND.COM

Any one of the following reasons could be the cause of this message

  • COMMAND.COM file was deleted or renamed.
  • COMMAND.COM wrong version
  • COMMAND.COM has a damaged header.
  • SOLUTION:
  • Use a Startup floppy (must be the same version or later as the system your trying to boot).
  • Type sys c: at the A:\> prompt and press enter.
  • Reboot
  • HIMEM.SYS not loaded

    The HIMEM.SYS command line in your config.sys file must appear before any commands that start programs or device drivers that use extended memory. If any of these other programs or devices try to load before HIMEM.SYS is loaded you could receive this error message.

    Missing or corrupt HIMEM.SYS

    The file may have been deleted from the C:\WINDOWS\COMMAND directory, or there is a line in CONFIG.SYS calling on a different version of HIMEM.SYS.

     

    SCSI

    The SCSI and CD-ROM support built into Windows requires that CD-ROM drives provide SCSI parity to function properly. For many drives, this is a configurable option or is active by default.

    The ends of the SCSI bus must have installed. In addition to the requirement that the last external and the last internal SCSI device be terminated, some hardware have additional requirements for where it must be placed in the SCSI chain.

    If Setup does not automatically detect a SCSI CD-ROM drive, try the following:

     

    • Try loading real-mode drivers for the SCSI controller, the CD-ROM driver, and Mscdex.exe, and see if the CD-ROM drive works in MS-DOS.
    • If the drive does work in MS-DOS, in Device Manager, examine the SCSI controller’s properties to make sure it was detected correctly.
    • Check your physical connections.
    • Check the SCSI IDs for all devices to make sure they are unique.

    A SCSI or IDE tape drive or scanner does not show up in Device Manager. Windows does not assign drive letters to tape drives and scanners, because they have no drive to assign a letter to. Therefore, they might appear as Unknown Devices in Device Manager. After you start Windows, it asks if you have a driver for these devices. If you have Windows drivers, click Yes, and then type the path to where the drivers are located. To use existing real-mode drivers, click No. Windows will continue to recognize and support these devices although they are listed as Unknown Devices.


    © Vibrant Worldwide Inc.
    RHCE Redhat Certification training | MCITP Boot Camp